Click Image for Gallery

Weldclass WC-03767 - 1.2mm 15kg Hardfacing CX-1800 Gasless MIG Wire

Features:

Long-Life hardfacing 'MIG' wire for ground-engaging equipment.
Very high resistance to abrasion with up to 3-4 times better wear life vs basic hardfacing wires
Special carbide additives not found in other wires.
Recommended for metal-to-earth applications where wear is mostly caused by abrasion, with low-to-medium impact; points, tynes, buckets, teeth, screws, augers, grousers, etc.
Gasless wire for easy application.
Available in 1.2mm in 15kg or 4.5kg spools.
Requires minimum 140 amps
Suitable for use with 200A-250A MIG welders.

Application Information:

Typical hardness 59-61 HRc (max hardness achieved with 2 layers)
Ideal for ground-engaging agricultural and earthmoving tools subject to high abrasion and low-to-moderate impact

Surface Preparation:

VERY IMPORTANT: Surface to be hard faced must be clean and free of rust, scale, grease, moisture & other contamination.
If existing/old hardfacing deposits are loose they should be removed. (Hammer test can confirm bond strength of existing deposits, a "ping" indicates good bond and a "clack" indicates a separation layer which must be ground off).
Buffer Layer / Pre-Heat: CX-1800 will typically weld easily to most common surfaces WITHOUT the need for buffer layer or pre-heat, such as mild & high carbon steel, cast steel, etc
If applying to hard-to-weld steels, or hard-to-weld existing deposits, use buffer layer of 309 or 312 wire or electrodes. Whilst not essential, pre-heat of 150-350c may be beneficial.
If applying to high-manganese (non-magnetic) steel, buffer of specialist high-Mn/Cr wire should be used.

Operating Data:

Polarity: DC+ (torch/wire positive)
Typical parameters: 140-200A @ 18-22V
VERY IMPORTANT: Amperage & voltage should be as low as possible within the recommended range. Applying excessive heat/voltage will reduce the performance and wear life of the weld deposit, due to excessive alloying with base material
Layers: Suitable for multi-layering (up to 3 layers)
Positions: Flat / downhand only (not suitable for vertical or overhead)

Finish:

Surface normally relief-checks (forms fine micro cracks) after welding
Weld deposit is NOT machineable
Weld deposit IS grind-able

How does platinum CX-1800 compare to hyundai CRC?

Composition: Both wires carry a high % of chromium (Cr) for abrasion resistance - however CX-1800 includes additional proprietary carbide additives not found in other wires, for very high abrasion resistance and long-life
Hardness: CrC = 54-57 HRc, CX-1800 = 59-61 HRc
Wear-life multiple vs mild-steel*: CrC = 430%, CX-1800 = 600%
Both wires are gasless, and are recommended for metal-to-earth applications where wear is mostly caused by abrasion, with low-to-medium impact
Summary: CX-1800 can be used in all applications where CrC is/has been used, but will offer longer service lift due to significantly higher abrasion resistance

*Approx, as per ASTM G65 standard

Specifications:

Wire: 1.2 mm
Spool Diameter: 300 mm
Weight: 15 kg

If you have any queries about Freight, please Call: 07 3326 1555 or Email: web@cltoolcentre.com.au

**We are able to dispatch goods Australia wide**

** Cut Off Time For Overnight Orders is 11:30 am Subject To Stock Availability **

** International orders are accepted at our discretion, Please contact our sales team for terms conditions & charges related to overseas orders**

Free Shipping - For Orders Over $99 (Conditions applied)

* WA Emergency Service: With key road and rail transport arrangements into and out of Western Australia significantly disrupted or unavailable, Auspost starts to charge an additional emergency measure cost of 40% (ex GST) of the freight charges. We have to temporarily exclude WA from the promotion of “Free Shipping For Orders Over $99 (Conditions applied)”.

C&L Tool Centre now offers free delivery for orders over $99 on a single transaction depending on shipping weight and Destination Zone. Please see the table below for details.

The total weight of the order must be below 20KG and the dimensions of the package have a maximum length of 1m and package volume of 0.25m³.

Items that exceed the above weights and dimensions or not meet requirements in Table1 may incur a freight charge and we will contact you prior to the dispatch to advise and confirm any freight charges.

This offer is valid for a limited time and C&L Tool Centre reserves the right to remove the offer without notice.

Table1:

Over $99 Free Shipping - Terms and Conditions
Destination Zone		Cart Total Requirement For Different Shipping Weight and Zone				Postcode
Destination Zone						Postcode
Zone	Name	0-3KG	3.01-6KG	6.01-10KG	10.01-20KG
Q0	Brisbane Metro	>=$99				4000-4018, 4029-4068, 4072-4123, 4127-4129, 4131-4132, 4151-4164, 4169-4182, 4205-4206, 9000-9725
Q1	Brisbane					4019-4028, 4069-4071, 4124-4126, 4130, 4133-4150, 4165-4168, 4183-4204, 4207-4209, 4270-4299, 4500-4549
GC	Gold Coast					4210-4224, 4226-4269, 9726-9919
IP	Ipswich					4300-4308
SC	Sunshine Coast					4550-4579
N0	Sydney Metro	>=$99		>=$199		1000-1935, 2000-2079, 2085-2107, 2109-2156, 2158, 2160-2172, 2174-2229, 2232-2249, 2557-2559, 2564-2567, 2740-2744, 2747- 2751, 2759-2764, 2766-2774, 2776-2777, 2890-2897
N1	Sydney					2080-2084, 2108, 2157, 2159, 2173, 2230-2231, 2508-2514, 2555-2556, 2560-2563, 2568-2574, 2745-2746, 2752-2758, 2765, 2775, 2778-2786
N4	Tweed Heads					2485-2486
V0	Melbourne Metro					3000-3062, 3064-3098, 3101-3138, 3140-3210, 3800-3801, 8000-8999, 9999
V1	Melbourne					3063, 3099-3100, 3139, 3335-3341, 3427-3443, 3750-3799, 3802-3811, 3910-3920, 3926-3944, 3975-3978, 3980-3983
Q5	Coolangatta					4225
Q2	QLD Country Near					4309-4453, 4580-4693
Q3	QLD Country Mid	>=$99	>=$199	>=$299	>=$399	4454-4499, 4694-4802, 4804-4805, 9920-9960
GF	Gosford					2250-2263
WG	Wollongong					2500-2507, 2515-2532
NC	Newcastle					2282-2310
CB	Canberra					200-299, 2600-2620, 2900-2920
S0	Adelaide Metro					5000-5113, 5115-5117, 5125-5130, 5158-5169, 5800-5999
S1	Adelaide					5114, 5118-5124, 5131-5157, 5170-5200
N3	Albury					1936-1999, 2640-2641, 2708-2709
N2	NSW Country					2264-2281, 2311-2484, 2487-2499, 2533-2554, 2575-2599, 2621-2639, 2642-2647, 2649-2707, 2710-2714, 2716, 2720-2730, 2787- 2879
V3	Wodonga					3689-3690
Q4	QLD Country North					4803, 4806-4999, 9961-9998
GL	Geelong					3211-3220
W0	Perth Metro					6000-6030, 6036, 6050-6066, 6069, 6076, 6090-6110, 6112-6120, 6147-6160, 6162-6175, 6180, 6182-6206, 6210, 6800-6990, 6992- 6996
W1	Perth					6031-6035, 6037-6049, 6067-6068, 6070-6075, 6077-6089, 6111, 6121-6146, 6161, 6176-6179, 6181, 6207-6209, 6211-6214, 6991, 6997-6999
T0	Tasmania Select	>=$199	>=$299	>=$399	>=$699	7000-7019, 7050-7053, 7055-7108, 7172, 7248-7254, 7258-7329, 7800-7999
T1	Tasmania					7020-7049, 7054, 7109-7150, 7155-7171, 7173-7247, 7255-7257, 7330-7799
BR	Ballarat					3350, 3353-3356
V2	VIC Country					2648, 2715, 2717-2719, 2731-2739, 3221-3334, 3342-3349, 3351-3352, 3357-3426, 3444-3688, 3691-3749, 3812-3909, 3921-3925, 3945-3974, 3979, 3984-3999
AAT	Aust Antarctic Territory*					7151-7154
S2	SA Country					2880-2889, 5201-5749
NT1	NT Near					0800-0802, 0804-0821, 0828-0851, 0853-0853, 0860-0861, 0870-0871, 0873-0879, 0906-0999
NT2	NT Remote					0803-0803, 0822-0827, 0852-0852, 0854-0859, 0862-0869, 0872-0872, 0880-0905
NF	Norfolk Is*					2898-2899
W4	Christmas & Cocos Is*					6798-6799
W2	WA Country South					6215-6700
W3	WA Country North					6701-6797

Weldclass WC-03767 - 1.2mm 15kg Hardfacing CX-1800 Gasless MIG Wire

Views: 2334
Weldclass
Product Code: WC-03767
Warranty: